You agree that BobVila. All rights reserved. Expert advice from Bob Vila, the most trusted name in home improvement, home remodeling, home repair, and DIY. If you're thinking about installing one, first read our handy planning guide to see whether this retractable door system is right for you.
Don't want to do it yourself? Get free, no-commitment estimates from licensed general contractors near you. Find local pros. More From Bob Vila.
The Best Pocket Door Locks of Top Tips for Installing a New Door. The Best Door Handles and Knobs of Check for wiring or plumbing. A wall with pipes in it is not a good place to put a door. Wiring can be easily detected with a cheap voltage sensor.
Remove the existing door, if applicable. If you're replacing a door with a pocket door, you'll need to get rid of the existing door. Start with removing the molding and, with a reciprocating saw blade, cut the shims. When the nails are cut, you can remove the door frame. Remove the drywall on one side of the wall. Do this slowly to make sure you haven't missed any obstacles within the wall.
Cut the exposed studs carefully. This makes room for the new framing. You may find this step easier if you use a combination of a circular saw and a small hand saw; you do not want to accidentally damage the wall you did not cut away. The goal is to leave large enough holes in the studs to allow the pocket door to pass through. A standard pocket door is 1. To make this step even easier, look for a pocket door kit that comes with split studs.
Part 2. Make a new header, if necessary. It's possible that your door will require a header of a different height. If the floor covering above the subfloor is minimal, the split-stud brackets can be secured directly to the floor. Once the appropriate length is determined, install a new stud this length from the existing stud on the opposing side. Nail the new header in place or screw and then cut and fit the soleplate to the floor.
To adjust the header, use a reciprocating saw to remove the partition header currently in place. Then, cut away the studs, just like in the above, to make space for the framing.
Cut the nails that are between the studs and the soleplate and then determine the height of your desired header before cutting the stud tops to length. Otherwise, you may end up with a frame that is not to size. Install the slider track. Your pocket door kit should contain the rails on which the door slides into the wall. Install the slider track using the directions that come with your pocket door kit, screwing the brackets into the studs. If you are also installing pre-split studs, you can install them after you install the slider track.
Most, if not all, kits come with these markers. Use a hacksaw on the channel and a handsaw on the nailers. Make sure your track is level. If it's not, it won't slide easily in and out of its pocket. Place the hardware and the door into the slider track. Make sure that the door is sliding easily and stays level. Mount hangers on the top of the door — this is how the door will slide.
No matter how well you plumbed the trimmer, you'll probably find a gap between the top or bottom of the door and the jamb. You can correct this by adjusting the shims, the hangers or both.
When the door butts cleanly against the jamb, you're ready to hang drywall, trim out the door opening and install the pocket door lock. Always take important safety precautions when working with tools, such as dawning a pair of safety goggles, a dust mask, and a pair of protective gloves.
Remodelaholic recommends consulting an engineer if you have any questions about the structure of the home. Related Articles. How do you lock a door that slides? Your privacy is safe, even if your pocket door is in the bathroom. Sometimes, a change in colour is all you need. Of course, it would be a bit safer to remove the door from the track first! Some people love the retro look of older doors , and the fact is — you can replace the sliding door with anything that will fit into the wall mechanism.
You can also use barn-style doors or regular doors, as long as they measure up. Check out this great example of installing retro-looking doors in a pocket door space — this is a perfect option if you have an old house and want modern solutions with an antique spirit! All you have to do is lift the door off the sliding track. In order to do that, you have to remove the trim around the door. New doors have release tabs that you can pop open with a screwdriver. To replace the whole door, you have to get the old door out by using the same method — getting the trim off.
You will need a screwdriver and some prying tools. Pocket doors are always a good idea — especially if you have limited space in your home.
0コメント